Ford Festiva Recalls
Vehicle manufacturers issue official Ford Festiva recall notices to inform car owners of problems and/or defects that have been brought to the manufacturer's attention. An automotive recall requires the manufacturer to send an official notice to owners of the vehicles found to be defective once the NHTSA deems the problem to be wide spread and an official Ford Festiva recall. View listings of Ford Festiva recalls from NHTSA below with full details, vehicles affected, date reported, and more.
|
|
 |
Used 1993 Ford Festiva Recalls
Components: SUSPENSION:FRONT:CONTROL ARM
Cars Affected: 94
Summary:
EQUIPMENT DESCRIPTION: AFTERMARKET BALL JOINT/CONTROL ARM MANUFACTURED BY MOOG INDUSTRIES. DUE TO MISPACKAGING, CERTAIN BALL JOINT/CONTROL ARM ASSEMBLIES WERE INCORRECTLY PLACED IN THE WRONG BOXES.
Consequences:
THESE BALL JOINT/CONTROL ARM ASSEMBLIES WILL NOT FIT INTO THE FRAME RECESS WITHOUT BEING ALTERED. ALSO THE STUD IS UNDERSIZED AND WILL NOT FIT THE SPINDLE PROPERLY POSSIBLY CAUSING A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy:
MOOG WILL REPLACE THE INCORRECTLY PACKAGED ASSEMBLIES WITH CORRECT BALL JOINT/CONTROL ARM ASSEMBLIES.
|
|
|
Used 1992 Ford Festiva Recalls
Components: SUSPENSION:FRONT:CONTROL ARM
Cars Affected: 94
Summary:
EQUIPMENT DESCRIPTION: AFTERMARKET BALL JOINT/CONTROL ARM MANUFACTURED BY MOOG INDUSTRIES. DUE TO MISPACKAGING, CERTAIN BALL JOINT/CONTROL ARM ASSEMBLIES WERE INCORRECTLY PLACED IN THE WRONG BOXES.
Consequences:
THESE BALL JOINT/CONTROL ARM ASSEMBLIES WILL NOT FIT INTO THE FRAME RECESS WITHOUT BEING ALTERED. ALSO THE STUD IS UNDERSIZED AND WILL NOT FIT THE SPINDLE PROPERLY POSSIBLY CAUSING A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy:
MOOG WILL REPLACE THE INCORRECTLY PACKAGED ASSEMBLIES WITH CORRECT BALL JOINT/CONTROL ARM ASSEMBLIES.
|
|
|
Used 1991 Ford Festiva Recalls
Components: SUSPENSION:FRONT:CONTROL ARM
Cars Affected: 94
Summary:
EQUIPMENT DESCRIPTION: AFTERMARKET BALL JOINT/CONTROL ARM MANUFACTURED BY MOOG INDUSTRIES. DUE TO MISPACKAGING, CERTAIN BALL JOINT/CONTROL ARM ASSEMBLIES WERE INCORRECTLY PLACED IN THE WRONG BOXES.
Consequences:
THESE BALL JOINT/CONTROL ARM ASSEMBLIES WILL NOT FIT INTO THE FRAME RECESS WITHOUT BEING ALTERED. ALSO THE STUD IS UNDERSIZED AND WILL NOT FIT THE SPINDLE PROPERLY POSSIBLY CAUSING A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy:
MOOG WILL REPLACE THE INCORRECTLY PACKAGED ASSEMBLIES WITH CORRECT BALL JOINT/CONTROL ARM ASSEMBLIES.
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 265,000
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THAT LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
|
|
|
Used 1990 Ford Festiva Recalls
Components: SUSPENSION:FRONT:CONTROL ARM
Cars Affected: 94
Summary:
EQUIPMENT DESCRIPTION: AFTERMARKET BALL JOINT/CONTROL ARM MANUFACTURED BY MOOG INDUSTRIES. DUE TO MISPACKAGING, CERTAIN BALL JOINT/CONTROL ARM ASSEMBLIES WERE INCORRECTLY PLACED IN THE WRONG BOXES.
Consequences:
THESE BALL JOINT/CONTROL ARM ASSEMBLIES WILL NOT FIT INTO THE FRAME RECESS WITHOUT BEING ALTERED. ALSO THE STUD IS UNDERSIZED AND WILL NOT FIT THE SPINDLE PROPERLY POSSIBLY CAUSING A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy:
MOOG WILL REPLACE THE INCORRECTLY PACKAGED ASSEMBLIES WITH CORRECT BALL JOINT/CONTROL ARM ASSEMBLIES.
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 265,000
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THAT LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
Components: SEAT BELTS:FRONT:WARNING LIGHT/DEVICES
Cars Affected: 268
Summary:
THE "FASTEN SEAT BELTS" WARNING LIGHTS MAY NOT WORK WHEN THE IGNITION IS SWITCHED TO THE "ON" POSITION DURING COLD AMBIENT TEMPERATURES.
Consequences:
OCCUPANTS WOULD NOT RECEIVE THIS WARNING TO USE SAFETY BELTS AND CARS WOULD NOT COMPLY WITH FMVSS 208.
Remedy:
FORD WILL REPLACE INSTRUMENT CLUSTERS IN THE AFFECTED CARS.
|
|
|
Used 1989 Ford Festiva Recalls
Components: SUSPENSION:FRONT:CONTROL ARM
Cars Affected: 94
Summary:
EQUIPMENT DESCRIPTION: AFTERMARKET BALL JOINT/CONTROL ARM MANUFACTURED BY MOOG INDUSTRIES. DUE TO MISPACKAGING, CERTAIN BALL JOINT/CONTROL ARM ASSEMBLIES WERE INCORRECTLY PLACED IN THE WRONG BOXES.
Consequences:
THESE BALL JOINT/CONTROL ARM ASSEMBLIES WILL NOT FIT INTO THE FRAME RECESS WITHOUT BEING ALTERED. ALSO THE STUD IS UNDERSIZED AND WILL NOT FIT THE SPINDLE PROPERLY POSSIBLY CAUSING A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy:
MOOG WILL REPLACE THE INCORRECTLY PACKAGED ASSEMBLIES WITH CORRECT BALL JOINT/CONTROL ARM ASSEMBLIES.
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 265,000
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THAT LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
|
|
|
Used 1988 Ford Festiva Recalls
Components: SUSPENSION:FRONT:CONTROL ARM
Cars Affected: 94
Summary:
EQUIPMENT DESCRIPTION: AFTERMARKET BALL JOINT/CONTROL ARM MANUFACTURED BY MOOG INDUSTRIES. DUE TO MISPACKAGING, CERTAIN BALL JOINT/CONTROL ARM ASSEMBLIES WERE INCORRECTLY PLACED IN THE WRONG BOXES.
Consequences:
THESE BALL JOINT/CONTROL ARM ASSEMBLIES WILL NOT FIT INTO THE FRAME RECESS WITHOUT BEING ALTERED. ALSO THE STUD IS UNDERSIZED AND WILL NOT FIT THE SPINDLE PROPERLY POSSIBLY CAUSING A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy:
MOOG WILL REPLACE THE INCORRECTLY PACKAGED ASSEMBLIES WITH CORRECT BALL JOINT/CONTROL ARM ASSEMBLIES.
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 265,000
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THAT LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
|
|
|
|
|
