Mitsubishi Precis Recalls
Vehicle manufacturers issue official Mitsubishi Precis recall notices to inform car owners of problems and/or defects that have been brought to the manufacturer's attention. An automotive recall requires the manufacturer to send an official notice to owners of the vehicles found to be defective once the NHTSA deems the problem to be wide spread and an official Mitsubishi Precis recall. View listings of Mitsubishi Precis recalls from NHTSA below with full details, vehicles affected, date reported, and more.
|
|
 |
Used 1994 Mitsubishi Precis Recalls
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 12,890
Summary:
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
Consequences:
IN THE EVENT OF AN ACCIDENT, THE FUEL SPILLAGE CAN RESULT IN A FIRE IF EXPOSED TO A SOURCE OF IGNITION.
Remedy:
MITSUBISHI HAS DEVELOPED AN APPROPRIATE COUNTERMEASURE THAT WILL COMPLY WITH ALL REQUIREMENTS OF FMVSS 301.
|
|
|
Used 1993 Mitsubishi Precis Recalls
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 12,890
Summary:
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
Consequences:
IN THE EVENT OF AN ACCIDENT, THE FUEL SPILLAGE CAN RESULT IN A FIRE IF EXPOSED TO A SOURCE OF IGNITION.
Remedy:
MITSUBISHI HAS DEVELOPED AN APPROPRIATE COUNTERMEASURE THAT WILL COMPLY WITH ALL REQUIREMENTS OF FMVSS 301.
|
|
|
Used 1992 Mitsubishi Precis Recalls
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 12,890
Summary:
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
Consequences:
IN THE EVENT OF AN ACCIDENT, THE FUEL SPILLAGE CAN RESULT IN A FIRE IF EXPOSED TO A SOURCE OF IGNITION.
Remedy:
MITSUBISHI HAS DEVELOPED AN APPROPRIATE COUNTERMEASURE THAT WILL COMPLY WITH ALL REQUIREMENTS OF FMVSS 301.
|
|
|
Used 1991 Mitsubishi Precis Recalls
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 12,890
Summary:
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
Consequences:
IN THE EVENT OF AN ACCIDENT, THE FUEL SPILLAGE CAN RESULT IN A FIRE IF EXPOSED TO A SOURCE OF IGNITION.
Remedy:
MITSUBISHI HAS DEVELOPED AN APPROPRIATE COUNTERMEASURE THAT WILL COMPLY WITH ALL REQUIREMENTS OF FMVSS 301.
|
|
|
Used 1990 Mitsubishi Precis Recalls
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 12,890
Summary:
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
Consequences:
IN THE EVENT OF AN ACCIDENT, THE FUEL SPILLAGE CAN RESULT IN A FIRE IF EXPOSED TO A SOURCE OF IGNITION.
Remedy:
MITSUBISHI HAS DEVELOPED AN APPROPRIATE COUNTERMEASURE THAT WILL COMPLY WITH ALL REQUIREMENTS OF FMVSS 301.
Components: WHEELS:CENTER SECTION
Cars Affected: 2,281
Summary:
LOCK WASHER LOCATED UNDER THE NUT THAT SECURES THE FRONT HUB TO THE DRIVE SHAFT MAY HAVE HAD IMPROPER HEAT TREATMENT AND COULD CRACK.
Consequences:
THIS COULD CAUSE WHEEL BEARING FREEPLAY AND COULD RESULT IN BEARING DAMAGE, AND POSSIBLE LOSS OF VEHICLE CONTROL THROUGH WHEEL FAILURE.
Remedy:
REPLACE LOCK WASHER ON EACH FRONT WHEEL AND REPAIR AREA AROUND LOCK WASHER AS NECESSARY.
|
|
|
Used 1989 Mitsubishi Precis Recalls
Components: VISIBILITY:DEFROSTER/DEFOGGER SYSTEM:WINDSHIELD...
Cars Affected: 1,906
Summary:
VEHICLES INVOLVED ARE THOSE THAT HAD THE HEATER VALVE STEMS REPLACED IN AN EARLIER MITSUBISHI RECALL (94V-103.001). CERTAIN VEHICLES HAD AN INCORRECT VALVE STEM INSTALLED WHICH COULD CAUSE THE INCORRECT STEM TO LEAK AFTER A PERIOD OF TIME.
Consequences:
THIS CAN RESULT IN A BURN INJURY TO THE FRONT SEAT PASSENGER'S FEET AND LEGS.
Remedy:
DEALERS WILL INSPECT AND REPLACE INCORRECT VALVE STEMS.
Components: VISIBILITY:DEFROSTER/DEFOGGER SYSTEM:WINDSHIELD...
Cars Affected: 23,935
Summary:
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
Consequences:
THIS CAN RESULT IN A BURN INJURY TO THE FRONT SEAT PASSENGER'S FEET AND LEGS.
Remedy:
DEALERS WILL INSPECT AND REPLACE DEFECTIVE VALVE STEMS.
Components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
Cars Affected: 895,000
Summary:
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
Consequences:
THE MELTING PLASTIC AIR FILTER CASE MAY LEAD TO A FIREIN THE ENGINE COMPARTMENT.
Remedy:
REPLACE THE REED VALVE SUBASSEMBLY WITH ONE WHOSE METAL COMPONENTS ARE FABRICATED FROM CORROSION RESISTANT STAINLESS STEEL.
|
|
|
Used 1988 Mitsubishi Precis Recalls
Components: VISIBILITY:DEFROSTER/DEFOGGER SYSTEM:WINDSHIELD...
Cars Affected: 1,906
Summary:
VEHICLES INVOLVED ARE THOSE THAT HAD THE HEATER VALVE STEMS REPLACED IN AN EARLIER MITSUBISHI RECALL (94V-103.001). CERTAIN VEHICLES HAD AN INCORRECT VALVE STEM INSTALLED WHICH COULD CAUSE THE INCORRECT STEM TO LEAK AFTER A PERIOD OF TIME.
Consequences:
THIS CAN RESULT IN A BURN INJURY TO THE FRONT SEAT PASSENGER'S FEET AND LEGS.
Remedy:
DEALERS WILL INSPECT AND REPLACE INCORRECT VALVE STEMS.
Components: VISIBILITY:DEFROSTER/DEFOGGER SYSTEM:WINDSHIELD...
Cars Affected: 23,935
Summary:
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
Consequences:
THIS CAN RESULT IN A BURN INJURY TO THE FRONT SEAT PASSENGER'S FEET AND LEGS.
Remedy:
DEALERS WILL INSPECT AND REPLACE DEFECTIVE VALVE STEMS.
Components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
Cars Affected: 895,000
Summary:
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
Consequences:
THE MELTING PLASTIC AIR FILTER CASE MAY LEAD TO A FIREIN THE ENGINE COMPARTMENT.
Remedy:
REPLACE THE REED VALVE SUBASSEMBLY WITH ONE WHOSE METAL COMPONENTS ARE FABRICATED FROM CORROSION RESISTANT STAINLESS STEEL.
|
|
|
Used 1987 Mitsubishi Precis Recalls
Components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
Cars Affected: 895,000
Summary:
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
Consequences:
THE MELTING PLASTIC AIR FILTER CASE MAY LEAD TO A FIREIN THE ENGINE COMPARTMENT.
Remedy:
REPLACE THE REED VALVE SUBASSEMBLY WITH ONE WHOSE METAL COMPONENTS ARE FABRICATED FROM CORROSION RESISTANT STAINLESS STEEL.
Components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS...
Cars Affected: 321,000
Summary:
VEHICLE MAY FAIL TO CONFORM TO THE BRAKE FADE AND RECOVERY PORTION OF FMVSS 105.
Consequences:
THERE MAY BE A LOSS OF BRAKING EFFICIENCY DURINGREPEATED HARD APPLICATION OF BRAKES WHICH COULD RESULT IN A CRASH WITHOUT PRIORWARNING.
Remedy:
REPLACE FRONT BRAKE PADS WITH NEWLY DESIGNED SEMI METALLIC BRAKE PADS.
|
|
|
|
|
