Saab 9000 Recalls
Vehicle manufacturers issue official Saab 9000 recall notices to inform car owners of problems and/or defects that have been brought to the manufacturer's attention. An automotive recall requires the manufacturer to send an official notice to owners of the vehicles found to be defective once the NHTSA deems the problem to be wide spread and an official Saab 9000 recall. View listings of Saab 9000 recalls from NHTSA below with full details, vehicles affected, date reported, and more.
|
|
 |
Used 1998 Saab 9000 Recalls
Components: EQUIPMENT:OTHER:LABELS
Cars Affected: 39,313
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AIR BAG ALERT LABEL ON THE DRIVER SIDE VISOR WAS OMITTED. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."
Consequences:
THE VEHICLE OCCUPANT MAY NOT PROPERLY UNDERSTAND THE OPERATION OF THE AIR BAG SYSTEM AND THE NEED TO USE SEAT BELTS.
Remedy:
OWNERS WILL BE PROVIDED WITH AN ALERT LABEL TO BE INSTALLED ON THE VISIBLE SIDE OF THE DRIVER'S SUN VISOR. IF AN OWNER SO DESIRES, THEIR DEALER CAN INSTALL THE LABEL FOR THEM.
|
|
 |
Used 1997 Saab 9000 Recalls
Components: EQUIPMENT:OTHER:LABELS
Cars Affected: 39,313
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AIR BAG ALERT LABEL ON THE DRIVER SIDE VISOR WAS OMITTED. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."
Consequences:
THE VEHICLE OCCUPANT MAY NOT PROPERLY UNDERSTAND THE OPERATION OF THE AIR BAG SYSTEM AND THE NEED TO USE SEAT BELTS.
Remedy:
OWNERS WILL BE PROVIDED WITH AN ALERT LABEL TO BE INSTALLED ON THE VISIBLE SIDE OF THE DRIVER'S SUN VISOR. IF AN OWNER SO DESIRES, THEIR DEALER CAN INSTALL THE LABEL FOR THEM.
|
|
|
Used 1994 Saab 9000 Recalls
Components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
Cars Affected: 26,116
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. MOISTURE CAN ENTER THE AIR BAG INFLATABLE RESTRAINT ELECTRONIC CONTROL MODULE (ECM) AND CAUSE CORROSION ON PORTIONS OF THE ECM PRINTER CIRCUIT BOARDS.
Consequences:
THIS CORROSION CAN POSSIBLY CREATE OPEN CONNECTIONS IN CIRCUITS WHICH CONTROL THE RESTRAINT DEPLOYMENT, POSSIBLY CAUSING INADVERTENT AIR BAG DEPLOYMENT.
Remedy:
DEALERS WILL INSPECT THE EXTERIOR OF THE ECM. IF THERE IS NO INDICATION OF MOISTURE, A COVER WILL BE INSTALLED OVER THE ECM. IF THERE IS INDICATION OF MOISTURE, THE DEALER WILL REPLACE THE ECM AND INSTALL A COVER OVER THE NEW ECM.
Components: SERVICE BRAKES, HYDRAULIC:ANTILOCK:CONTROL UNIT...
Cars Affected: 12,091
Summary:
MOISTURE CAN FOLLOW THE ELECTRICAL HARNESS AND ENTER THE PRESSURE SWITCH CONNECTOR CAUSING CORROSION AND MALFUNCTION OF THE SWITCH.
Consequences:
THE CORROSION CAUSES A DETERIORATION OF THE ELECTRICALSWITCH CONNECTION AND CAN RESULT IN FALSE ILLUMINATION OF ABS AND/OR THE BRAKE WARNING LIGHTS AND/OR THE LOSS OF POWER ASSISTANCE BECAUSE OF NO HYDRAULIC PUMPOPERATION. LOSS OF POWER ASSIST INCREASES THE DRIVER'S BRAKE PEDAL EFFORT REQUIRED FOR STOPPING WHICH CAN RESULT IN EXTENDED BRAKING DISTANCES.
Remedy:
DEALERS WILL INSPECT THE ELECTRICAL CONNECTIONS TO THE ABS PRESSURE SWITCH TERMINALS FOR CORROSION AND INSTALL A SHRINK HOSE TO THE WIRING HARNESS TO AVOID MOISTURE ENTERING THE CONNECTION. PRESSURE SWITCHES WITH CORRODED CONNECTORS WILL BE REPLACED.
Components: ENGINE AND ENGINE COOLING:COOLING SYSTEM
Cars Affected: 12,040
Summary:
DURING LOW ENERGY FRONTAL IMPACT COLLISIONS, THE FRONT CROSSMEMBER CAN CONTACT THE METAL TUBING PORTION OF THE COOLER HOSE ASSEMBLY; AND/OR THE HOSE ASSEMBLY CAN BREAK AND LEAK OIL ONTO THE HOT EXHAUST MANIFOLD OR THE TURBOCHARGER.
Consequences:
OIL LEAKING ON THESE HOT ENGINE SURFACES CAN IGNITE AND CAUSE A VEHICULAR FIRE.
Remedy:
DEALERS WILL INSTALL A PROTECTIVE COVER WHICH WILL PROTECT THE COOLER AND HOSES FROM OTHER STRUCTURAL COMPONENTS IN LOW ENERGY FRONT IMPACTS.
Components: EXTERIOR LIGHTING:BRAKE LIGHTS
Cars Affected: 59
Summary:
ONE OF THE BULBS IN EACH OF THE BRAKE LIGHT LOWER OUTBOARD LAMP ASSEMBLIES MAY NOT HAVE BEEN PROPERLY WIRED, RESULTING IN IMPROPER TAIL LIGHT ILLUMINATION ON BRAKE APPLICATION. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."
Consequences:
CONSEQUENCE OF NON-COMPLIANCE: IMPROPER ILLUMINATION OF BRAKE LIGHTS DURING BRAKE APPLICATION MAY NOT SIGNAL FOLLOWING DRIVERS OF THE OPERATOR'S INTENT TO SLOW OR STOP AND COULD RESULT IN A VEHICLE COLLISION.
Remedy:
DEALERS WILL MODIFY THE BRAKE LIGHT OUTBOARD LAMP ASSEMBLIES TO MEET FMVSS REQUIREMENTS.
|
|
|
Used 1993 Saab 9000 Recalls
Components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
Cars Affected: 26,116
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. MOISTURE CAN ENTER THE AIR BAG INFLATABLE RESTRAINT ELECTRONIC CONTROL MODULE (ECM) AND CAUSE CORROSION ON PORTIONS OF THE ECM PRINTER CIRCUIT BOARDS.
Consequences:
THIS CORROSION CAN POSSIBLY CREATE OPEN CONNECTIONS IN CIRCUITS WHICH CONTROL THE RESTRAINT DEPLOYMENT, POSSIBLY CAUSING INADVERTENT AIR BAG DEPLOYMENT.
Remedy:
DEALERS WILL INSPECT THE EXTERIOR OF THE ECM. IF THERE IS NO INDICATION OF MOISTURE, A COVER WILL BE INSTALLED OVER THE ECM. IF THERE IS INDICATION OF MOISTURE, THE DEALER WILL REPLACE THE ECM AND INSTALL A COVER OVER THE NEW ECM.
Components: SERVICE BRAKES, HYDRAULIC:ANTILOCK:CONTROL UNIT...
Cars Affected: 12,091
Summary:
MOISTURE CAN FOLLOW THE ELECTRICAL HARNESS AND ENTER THE PRESSURE SWITCH CONNECTOR CAUSING CORROSION AND MALFUNCTION OF THE SWITCH.
Consequences:
THE CORROSION CAUSES A DETERIORATION OF THE ELECTRICALSWITCH CONNECTION AND CAN RESULT IN FALSE ILLUMINATION OF ABS AND/OR THE BRAKE WARNING LIGHTS AND/OR THE LOSS OF POWER ASSISTANCE BECAUSE OF NO HYDRAULIC PUMPOPERATION. LOSS OF POWER ASSIST INCREASES THE DRIVER'S BRAKE PEDAL EFFORT REQUIRED FOR STOPPING WHICH CAN RESULT IN EXTENDED BRAKING DISTANCES.
Remedy:
DEALERS WILL INSPECT THE ELECTRICAL CONNECTIONS TO THE ABS PRESSURE SWITCH TERMINALS FOR CORROSION AND INSTALL A SHRINK HOSE TO THE WIRING HARNESS TO AVOID MOISTURE ENTERING THE CONNECTION. PRESSURE SWITCHES WITH CORRODED CONNECTORS WILL BE REPLACED.
Components: ENGINE AND ENGINE COOLING:COOLING SYSTEM
Cars Affected: 12,040
Summary:
DURING LOW ENERGY FRONTAL IMPACT COLLISIONS, THE FRONT CROSSMEMBER CAN CONTACT THE METAL TUBING PORTION OF THE COOLER HOSE ASSEMBLY; AND/OR THE HOSE ASSEMBLY CAN BREAK AND LEAK OIL ONTO THE HOT EXHAUST MANIFOLD OR THE TURBOCHARGER.
Consequences:
OIL LEAKING ON THESE HOT ENGINE SURFACES CAN IGNITE AND CAUSE A VEHICULAR FIRE.
Remedy:
DEALERS WILL INSTALL A PROTECTIVE COVER WHICH WILL PROTECT THE COOLER AND HOSES FROM OTHER STRUCTURAL COMPONENTS IN LOW ENERGY FRONT IMPACTS.
Components: EXTERIOR LIGHTING:BRAKE LIGHTS:SWITCH
Cars Affected: 9,747
Summary:
A NUMBER OF BRAKE LIGHT SWITCHES HAVE AN OVAL-SHAPED PISTON WHICH CAN GET STUCK UNDER CERTAIN CONDITIONS. OTHER SWITCHES WERE MOUNTED SO THAT BOTH LOCKING TABS ARE NOT COMPLETELY ENGAGED IN THE MOUNTING BRACKET. IF ONE SIDE IS NOT ENGAGED, THE SWITCH IS MISALIGNED WITH THE PEDAL MECHANISM AND CAN BIND THE PISTON MOVEMENT, WHICH CAN CAUSE THE BRAKE LIGHT SWITCH TO STICK IN THE "OFF" OR "ON" POSITION.
Consequences:
THIS RESULTS IN EITHER THE BRAKE LIGHTS REMAINING ON CONSTANTLY OR THE BRAKE LIGHTS NOT ILLUMINATING WHEN THE BRAKES ARE APPLIED. THIS RESULTS IN INACCURATE SIGNALS OF BRAKE OPERATION TO OTHER VEHICLE OPERATORS, AND COULD RESULT IN AN ACCIDENT.
Remedy:
DEALERS WILL INSPECT BRAKE LIGHT SWITCHES. FOR VEHICLES WITH THE OVAL-SHAPED PISTON AND FOR VEHICLES WITH MISALIGNED BRAKE LIGHT SWITCHES, THE BRAKE LIGHT SWITCH WILL BE REPLACED.
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 5,824
Summary:
THE FUEL FILLER AND TANK VENTILATION HOSES MAY DEVELOP CRACKS UNDER THE SECURING HOSE CLAMPS, RESULTING IN FUEL LEAKAGE.
Consequences:
FUEL LEAKS MAY RESULT IN A FIRE IF AN IGNITION SOURCEIS PRESENT.
Remedy:
THE FUEL FILLER AND FUEL VENTILATION HOSES WILL BE REPLACED WITH NEW HOSES. THE FIVE SECURING HOSE CLAMPS WILL BE REPLACED BY A NEW TYPE WITH A SHIELD THAT PREVENTS DAMAGE TO THE HOSE WHEN TIGHTENED.
|
|
|
Used 1992 Saab 9000 Recalls
Components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
Cars Affected: 26,116
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. MOISTURE CAN ENTER THE AIR BAG INFLATABLE RESTRAINT ELECTRONIC CONTROL MODULE (ECM) AND CAUSE CORROSION ON PORTIONS OF THE ECM PRINTER CIRCUIT BOARDS.
Consequences:
THIS CORROSION CAN POSSIBLY CREATE OPEN CONNECTIONS IN CIRCUITS WHICH CONTROL THE RESTRAINT DEPLOYMENT, POSSIBLY CAUSING INADVERTENT AIR BAG DEPLOYMENT.
Remedy:
DEALERS WILL INSPECT THE EXTERIOR OF THE ECM. IF THERE IS NO INDICATION OF MOISTURE, A COVER WILL BE INSTALLED OVER THE ECM. IF THERE IS INDICATION OF MOISTURE, THE DEALER WILL REPLACE THE ECM AND INSTALL A COVER OVER THE NEW ECM.
Components: SERVICE BRAKES, HYDRAULIC:ANTILOCK:CONTROL UNIT...
Cars Affected: 12,091
Summary:
MOISTURE CAN FOLLOW THE ELECTRICAL HARNESS AND ENTER THE PRESSURE SWITCH CONNECTOR CAUSING CORROSION AND MALFUNCTION OF THE SWITCH.
Consequences:
THE CORROSION CAUSES A DETERIORATION OF THE ELECTRICALSWITCH CONNECTION AND CAN RESULT IN FALSE ILLUMINATION OF ABS AND/OR THE BRAKE WARNING LIGHTS AND/OR THE LOSS OF POWER ASSISTANCE BECAUSE OF NO HYDRAULIC PUMPOPERATION. LOSS OF POWER ASSIST INCREASES THE DRIVER'S BRAKE PEDAL EFFORT REQUIRED FOR STOPPING WHICH CAN RESULT IN EXTENDED BRAKING DISTANCES.
Remedy:
DEALERS WILL INSPECT THE ELECTRICAL CONNECTIONS TO THE ABS PRESSURE SWITCH TERMINALS FOR CORROSION AND INSTALL A SHRINK HOSE TO THE WIRING HARNESS TO AVOID MOISTURE ENTERING THE CONNECTION. PRESSURE SWITCHES WITH CORRODED CONNECTORS WILL BE REPLACED.
Components: ENGINE AND ENGINE COOLING:COOLING SYSTEM
Cars Affected: 12,040
Summary:
DURING LOW ENERGY FRONTAL IMPACT COLLISIONS, THE FRONT CROSSMEMBER CAN CONTACT THE METAL TUBING PORTION OF THE COOLER HOSE ASSEMBLY; AND/OR THE HOSE ASSEMBLY CAN BREAK AND LEAK OIL ONTO THE HOT EXHAUST MANIFOLD OR THE TURBOCHARGER.
Consequences:
OIL LEAKING ON THESE HOT ENGINE SURFACES CAN IGNITE AND CAUSE A VEHICULAR FIRE.
Remedy:
DEALERS WILL INSTALL A PROTECTIVE COVER WHICH WILL PROTECT THE COOLER AND HOSES FROM OTHER STRUCTURAL COMPONENTS IN LOW ENERGY FRONT IMPACTS.
Components: FUEL SYSTEM, GASOLINE
Cars Affected: 5,824
Summary:
THE FUEL FILLER AND TANK VENTILATION HOSES MAY DEVELOP CRACKS UNDER THE SECURING HOSE CLAMPS, RESULTING IN FUEL LEAKAGE.
Consequences:
FUEL LEAKS MAY RESULT IN A FIRE IF AN IGNITION SOURCEIS PRESENT.
Remedy:
THE FUEL FILLER AND FUEL VENTILATION HOSES WILL BE REPLACED WITH NEW HOSES. THE FIVE SECURING HOSE CLAMPS WILL BE REPLACED BY A NEW TYPE WITH A SHIELD THAT PREVENTS DAMAGE TO THE HOSE WHEN TIGHTENED.
|
|
|
Used 1991 Saab 9000 Recalls
Components: POWER TRAIN:AUTOMATIC TRANSMISSION
Cars Affected: 250
Summary:
IMPROPER ASSEMBLY COULD CAUSE THE BALL OF THE GEAR SELECTOR ARM NOT TO BE PROPERLY FIXED TO THE SOCKET ON THE END OF THE GEAR SELECTOR CABLE; GEAR SELECTOR ARM COULD SEPARATE FROM THE GEAR SELECTOR CABLE AT THE BALL SOCKET JOINT.
Consequences:
THE GEAR POSITION COULD NOT BE SELECTED OR DETERMINEDUSING THE SELECTOR LEVER; CAR COULD BE STARTED IN GEAR OTHER THAN PARK ORNEUTRAL, RESULTING IN SUDDEN UNEXPECTED VEHICLE MOVEMENT.
Remedy:
PROPERLY SEAT GEAR SELECTOR ARM BALL IN THE SELECTOR CABLE SOCKET AND SECURE BY A LOCK RING INSIDE THE SOCKET.
|
|
|
Used 1990 Saab 9000 Recalls
Components: ELECTRICAL SYSTEM:IGNITION:SWITCH
Cars Affected: 24,379
Summary:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.
Consequences:
THIS COULD CAUSE OVERHEATING OF THE SWITCH ASSEMBLY WITHSMOKE AND POSSIBLY A FIRE IN THE CENTER CONSOLE AREA.
Remedy:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.
|
|
|
Used 1989 Saab 9000 Recalls
Components: ELECTRICAL SYSTEM:IGNITION:SWITCH
Cars Affected: 24,379
Summary:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.
Consequences:
THIS COULD CAUSE OVERHEATING OF THE SWITCH ASSEMBLY WITHSMOKE AND POSSIBLY A FIRE IN THE CENTER CONSOLE AREA.
Remedy:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.
Components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS...
Cars Affected: 14,000
Summary:
THE ROUTING OF THE THROTTLE KICKDOWN CABLE COULD ALLOW CHAFING TO OCCUR BETWEEN THE CABLE AND ANY ONE OF THREE STEEL BRAKE FLUID LINES NEAR THE VALVE BLOCK OF THE HYDRAULIC BRAKE UNIT.
Consequences:
THIS COULD CAUSE BRAKE FLUID LEAKAGE; THUS, THE BRAKECIRCUIT SUPPLIED BY THAT LINE WOULD BECOME INOPERATIVE AND RESULT IN DECREASEDBRAKING EFFECTIVENESS AND AN ACCIDENT.
Remedy:
CHANGE CABLE ROUTING AND INSTALL NEW ATTACHMENT BRACKET TO PREVENT CHAFING.
Components: FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIP...
Cars Affected: 1,586
Summary:
FUEL FILTER MAY NOT MEET THE SPECIFICATION CONCERNING LEAKAGE CRITERIA DUE TO LOW TEMPERATURE DURING THE GLUING PROCESS.
Consequences:
FUEL FILTER MAY LEAK CREATING A POTENTIAL FIRE HAZARD.
Remedy:
REPLACE FUEL FILTER.
|
|
|
Used 1988 Saab 9000 Recalls
Components: ELECTRICAL SYSTEM:IGNITION:SWITCH
Cars Affected: 24,379
Summary:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.
Consequences:
THIS COULD CAUSE OVERHEATING OF THE SWITCH ASSEMBLY WITHSMOKE AND POSSIBLY A FIRE IN THE CENTER CONSOLE AREA.
Remedy:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.
Components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS...
Cars Affected: 14,000
Summary:
THE ROUTING OF THE THROTTLE KICKDOWN CABLE COULD ALLOW CHAFING TO OCCUR BETWEEN THE CABLE AND ANY ONE OF THREE STEEL BRAKE FLUID LINES NEAR THE VALVE BLOCK OF THE HYDRAULIC BRAKE UNIT.
Consequences:
THIS COULD CAUSE BRAKE FLUID LEAKAGE; THUS, THE BRAKECIRCUIT SUPPLIED BY THAT LINE WOULD BECOME INOPERATIVE AND RESULT IN DECREASEDBRAKING EFFECTIVENESS AND AN ACCIDENT.
Remedy:
CHANGE CABLE ROUTING AND INSTALL NEW ATTACHMENT BRACKET TO PREVENT CHAFING.
Components: VEHICLE SPEED CONTROL
Cars Affected: 7,000
Summary:
THE BALL CHAIN BETWEEN THE CRUISE CONTROL VACUUM REGULATOR AND THE ACCELERATOR PEDAL ARM MAY CATCH ON THE VACUUM REGULATOR ATTACHMENT CLIP.
Consequences:
IF THE CHAIN GETS CAUGHT THE THROTTLE COULD BE PREVENTEDFROM RETURNING TO FULLY CLOSED POSITION WHEN THE ACCELERATOR PEDAL IS RELEASED.
Remedy:
A PLASTIC CAP WILL BE INSTALLED OVER THE VACUUM REGULATOR CLIP TO COVER THE OPENINGS.
|
|
|
Used 1987 Saab 9000 Recalls
Components: ELECTRICAL SYSTEM:IGNITION:SWITCH
Cars Affected: 24,379
Summary:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.
Consequences:
THIS COULD CAUSE OVERHEATING OF THE SWITCH ASSEMBLY WITHSMOKE AND POSSIBLY A FIRE IN THE CENTER CONSOLE AREA.
Remedy:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.
|
|
|
Used 1986 Saab 9000 Recalls
Components: ELECTRICAL SYSTEM:IGNITION:SWITCH
Cars Affected: 24,379
Summary:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.
Consequences:
THIS COULD CAUSE OVERHEATING OF THE SWITCH ASSEMBLY WITHSMOKE AND POSSIBLY A FIRE IN THE CENTER CONSOLE AREA.
Remedy:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.
Components: ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH
Cars Affected: 9,590
Summary:
THE WIRING HARNESS MAY CHAFE AGAINST THE WINDSHIELD WIPER MOTOR BRACKET. CONSEQUENCE OF DEFECT: IF A SHORT CIRCUIT DEVELOPS, IT COULD RESULT IN A FIRE.
Consequences:
Remedy:
AFFIX TWO RUBBER STRIPS TO THE VERTICAL EDGES OF THE WINDSHIELD WIPER MOTOR BRACKET.
|
|
|
|
|
