Suzuki Swift Recalls
Vehicle manufacturers issue official Suzuki Swift recall notices to inform car owners of problems and/or defects that have been brought to the manufacturer's attention. An automotive recall requires the manufacturer to send an official notice to owners of the vehicles found to be defective once the NHTSA deems the problem to be wide spread and an official Suzuki Swift recall. View listings of Suzuki Swift recalls from NHTSA below with full details, vehicles affected, date reported, and more.
|
|
 |
Used 2000 Suzuki Swift Recalls
Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
Cars Affected: 1,593
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 225.S12, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THE OWNER'S MANUALS ACCOMPANYING THESE VEHICLES DO NOT HAVE CERTAIN WRITTEN INSTRUCTIONS AS REQUIRED BY THE STANDARD.
Consequences:
IN THE EVENT OF A CRASH, THE CHILD SEAT MAY NOT BE PROPERLY ATTACHED INCREASING THE RISK OF INJURY TO THE CHILD.
Remedy:
OWNERS WILL BE SENT A NEW OWNER'S MANUAL THAT CONTAINS THE INFORMATION AS REQUIRED BY FMVSS NO. 225.
|
|
 |
Used 1997 Suzuki Swift Recalls
Components: POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL...
Cars Affected: 1,198
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSAXLE. THE SHIFT LEVER APPEARS TO BE IN "PARK," BUT CAN EASILY BE MOVED FROM THE "PARK" POSITION WITHOUT THE USE OF THE KEY, TRANSAXLE LEVER DETENT BUTTON, OR DEPRESSING THE BRAKE.
Consequences:
IF THE SHIFT LEVER WERE TO COME OUT OF "PARK" WHILE THE VEHICLE IS PARKED ON A NON-LEVEL SURFACE, THE VEHICLE COULD ROLL INCREASING THE RISK OF A CRASH.
Remedy:
DEALERS WILL REPLACE THE SHIFTER ASSEMBLY. UNTIL THE VEHICLE IS SERVICED, OWNERS ARE ADVISED WHEN SHIFTING TO "PARK," ALWAYS APPLY THE PARK BRAKE BEFORE RELEASING THE SERVICE BRAKE.
|
|
|
Used 1993 Suzuki Swift Recalls
Components: LATCHES/LOCKS/LINKAGES:HOOD:LATCH
Cars Affected: 38,229
Summary:
MISLOCATED ATTACHING SPOT WELDS OF THE HOOD STRIKER ASSEMBLY CAUSE CRACKS TO START ON THE HOOD INNER PANEL. IF CRACKS OCCUR, THE HOOD STRIKER ASSEMBLY MAY NOT PROPERLY ENGAGE THE HOOD LATCH WHEN THE HOOD IS CLOSED.
Consequences:
AN IMPROPERLY ENGAGED HOOD LATCH MAY RESULT IN A HOOD FLY-UP WHILE THE VEHICLE IS IN MOTION. THIS COULD OBSTRUCT THE DRIVER'S VIEW AND COULD CAUSE A VEHICLE CRASH.
Remedy:
SUZUKI WILL (A) INSTALL TWO BOLTS AND NUTS TO SECURE THE STRIKER ASSEMBLY TO THE HOOD INNER PANEL, AND (B) ENSURE THAT THE HOOD LATCH ASSEMBLY FASTENERS ARE PROPERLY TIGHTENED.
|
|
|
Used 1992 Suzuki Swift Recalls
Components: LATCHES/LOCKS/LINKAGES:HOOD:LATCH
Cars Affected: 38,229
Summary:
MISLOCATED ATTACHING SPOT WELDS OF THE HOOD STRIKER ASSEMBLY CAUSE CRACKS TO START ON THE HOOD INNER PANEL. IF CRACKS OCCUR, THE HOOD STRIKER ASSEMBLY MAY NOT PROPERLY ENGAGE THE HOOD LATCH WHEN THE HOOD IS CLOSED.
Consequences:
AN IMPROPERLY ENGAGED HOOD LATCH MAY RESULT IN A HOOD FLY-UP WHILE THE VEHICLE IS IN MOTION. THIS COULD OBSTRUCT THE DRIVER'S VIEW AND COULD CAUSE A VEHICLE CRASH.
Remedy:
SUZUKI WILL (A) INSTALL TWO BOLTS AND NUTS TO SECURE THE STRIKER ASSEMBLY TO THE HOOD INNER PANEL, AND (B) ENSURE THAT THE HOOD LATCH ASSEMBLY FASTENERS ARE PROPERLY TIGHTENED.
|
|
|
Used 1991 Suzuki Swift Recalls
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 127,155
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
Components: LATCHES/LOCKS/LINKAGES:HOOD:LATCH
Cars Affected: 38,229
Summary:
MISLOCATED ATTACHING SPOT WELDS OF THE HOOD STRIKER ASSEMBLY CAUSE CRACKS TO START ON THE HOOD INNER PANEL. IF CRACKS OCCUR, THE HOOD STRIKER ASSEMBLY MAY NOT PROPERLY ENGAGE THE HOOD LATCH WHEN THE HOOD IS CLOSED.
Consequences:
AN IMPROPERLY ENGAGED HOOD LATCH MAY RESULT IN A HOOD FLY-UP WHILE THE VEHICLE IS IN MOTION. THIS COULD OBSTRUCT THE DRIVER'S VIEW AND COULD CAUSE A VEHICLE CRASH.
Remedy:
SUZUKI WILL (A) INSTALL TWO BOLTS AND NUTS TO SECURE THE STRIKER ASSEMBLY TO THE HOOD INNER PANEL, AND (B) ENSURE THAT THE HOOD LATCH ASSEMBLY FASTENERS ARE PROPERLY TIGHTENED.
|
|
|
Used 1990 Suzuki Swift Recalls
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 127,155
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
Components: LATCHES/LOCKS/LINKAGES:HOOD:LATCH
Cars Affected: 38,229
Summary:
MISLOCATED ATTACHING SPOT WELDS OF THE HOOD STRIKER ASSEMBLY CAUSE CRACKS TO START ON THE HOOD INNER PANEL. IF CRACKS OCCUR, THE HOOD STRIKER ASSEMBLY MAY NOT PROPERLY ENGAGE THE HOOD LATCH WHEN THE HOOD IS CLOSED.
Consequences:
AN IMPROPERLY ENGAGED HOOD LATCH MAY RESULT IN A HOOD FLY-UP WHILE THE VEHICLE IS IN MOTION. THIS COULD OBSTRUCT THE DRIVER'S VIEW AND COULD CAUSE A VEHICLE CRASH.
Remedy:
SUZUKI WILL (A) INSTALL TWO BOLTS AND NUTS TO SECURE THE STRIKER ASSEMBLY TO THE HOOD INNER PANEL, AND (B) ENSURE THAT THE HOOD LATCH ASSEMBLY FASTENERS ARE PROPERLY TIGHTENED.
|
|
|
Used 1989 Suzuki Swift Recalls
Components: SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Cars Affected: 127,155
Summary:
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
Consequences:
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
Remedy:
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
Components: LATCHES/LOCKS/LINKAGES:HOOD:LATCH
Cars Affected: 38,229
Summary:
MISLOCATED ATTACHING SPOT WELDS OF THE HOOD STRIKER ASSEMBLY CAUSE CRACKS TO START ON THE HOOD INNER PANEL. IF CRACKS OCCUR, THE HOOD STRIKER ASSEMBLY MAY NOT PROPERLY ENGAGE THE HOOD LATCH WHEN THE HOOD IS CLOSED.
Consequences:
AN IMPROPERLY ENGAGED HOOD LATCH MAY RESULT IN A HOOD FLY-UP WHILE THE VEHICLE IS IN MOTION. THIS COULD OBSTRUCT THE DRIVER'S VIEW AND COULD CAUSE A VEHICLE CRASH.
Remedy:
SUZUKI WILL (A) INSTALL TWO BOLTS AND NUTS TO SECURE THE STRIKER ASSEMBLY TO THE HOOD INNER PANEL, AND (B) ENSURE THAT THE HOOD LATCH ASSEMBLY FASTENERS ARE PROPERLY TIGHTENED.
|
|
|
|
